How to Set up a Tub: Install an Acrylic Bathtub as Well as Bathtub Surround
How to Set up a Tub: Install an Acrylic Bathtub as Well as Bathtub Surround
Blog Article
This great article following next relating to A Step-by-Step Guide to Installing a Bathtub is relatively enlightening. Don't miss out on it.
Installing a bathtub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult job. If the old bathtub is conveniently easily accessible, the job can move quickly; if you have to open up a wall to get rid of the old tub and also position the brand-new bath tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly require an assistant to vacate the old tub and also embeded in the brand-new one. Make sure you have actually qualified on your own for the job as well as fit attempting it. As opposed to employing a service provider to take over a halfway-completed task, it is much better to take into consideration utilizing one before you start. Chances are you might need a professional plumber to make tube links.
This short article will certainly assist you install a brand-new bathtub in your washroom if you have actually already gotten a new bathtub and do not need to transform the arrangement of your previous water pipes.
Your devices as well as product checklist should make up the following:
Getting ready for the Installation
To start with, the sustaining frame provided with the bath must be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the tap features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to prevent stress on the bath tub.
Fit the flexible faucet ports to the bottom of both faucets using 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now prepare to be suited its last setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, switch on the faucets to drain pipes any water staying in the system. The process of removing the existing taps can be quite problematic due to the limited accessibility that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the staying water that will come from the pipes. Once the supply pipes have been removed, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this process. When the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before proceeding to fit the new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Making use of both wood boards under its feet, position the bath tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little points.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level and also readjusting the feet on the tub until the level checks out level.
To mount taps, fit all-time low of the outermost flexible faucet port to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as inspect all joints and brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as also examine the overflow outlet and also the typical outlet for leakages.
Finally, take care of the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub must wait until the bath tub has been made use of at least when as this will resolve it into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the maker provided backnut. Once the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous type ought to be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bath fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a rigid seal, triggering the water to pass through the wall surface between the bath as well as the tiling, bring about problems with moisture and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and also fittings. They are marketed in tubes and cartridges, as well as can securing gaps up to a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill up the tub with water prior to securing, to enable the activity experienced when the bathtub is in use. The sealant can break relatively early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily available on the market. It is advisable to fit the tiles using water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very eager about Installing A Bathtub and I hope you appreciated our blog post. Those who enjoyed reading our blog post if you please don't forget to share it. Thanks for taking the time to read it.
Book A Service
Report this page